wavebubble:wave_bubble_2010
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
wavebubble:wave_bubble_2010 [2011/01/16 16:28] mictronics Added schematic and layout file |
wavebubble:wave_bubble_2010 [2011/05/12 19:38] aqisnotliquid |
||
|---|---|---|---|
| Line 42: | Line 42: | ||
| ^Name ^Value ^Package ^DIGIKEY ^ | ^Name ^Value ^Package ^DIGIKEY ^ | ||
| |BAT1 |LiPo 3.7V/1800mAh |BATTERY | | |BAT1 |LiPo 3.7V/1800mAh |BATTERY | | ||
| - | |C1 |100n |1206 |399-1249-1-ND | | + | |C1 |.10 uF, 50V |1206 |399-1249-1-ND | |
| - | |C2 |100n |1206 |399-1249-1-ND | | + | |C2 |.10 uF, 50V |1206 |399-1249-1-ND | |
| - | |C3 |100n |1206 |399-1249-1-ND | | + | |C3 |.10 uF, 50V |1206 |399-1249-1-ND | |
| - | |C4 |100n |1206 |399-1249-1-ND | | + | |C4 |.10 uF, 50V |1206 |399-1249-1-ND | |
| - | |C5 |1u |1206 |490-1832-1-ND | | + | |C5 |1uF, 25V |1206 |490-1832-1-ND | |
| - | |C6 |220u/6.3V |SMD_R8X5,4_ELKO |493-2156-1-ND | | + | |C6 |220uF, 6.3V |SMD_R8X5,4_ELKO |493-2156-1-ND | |
| - | |C7 |47u/6.3V |SMD_R5X5,4_ELKO |493-2086-1-ND | | + | |C7 |47uF, 6.3V |SMD_R5X5,4_ELKO |493-2086-1-ND | |
| |C8 |1u |1206 |490-1832-1-ND | | |C8 |1u |1206 |490-1832-1-ND | | ||
| |C9 |47n |1206 |399-1246-1-ND | | |C9 |47n |1206 |399-1246-1-ND | | ||
| Line 169: | Line 169: | ||
| \\ | \\ | ||
| Digikey BOM ID: 22247 | Digikey BOM ID: 22247 | ||
| + | |||
| + | |||
| + | == Errata == | ||
| + | |||
| + | Rev. 2b | ||
| + | * Nothing to report so far. | ||
| + | |||
| + | == Hints & Testing == | ||
| + | |||
| + | Wavebubble2010 Firmware for hardware tests: {{:wavebubble:wb2010_hardware_test.zip|}}\\ | ||
| + | The ZIP contains the sourcecode and a precompiled .hex file for the ATmega168V.\\ | ||
| + | \\ | ||
| + | Flash the .hex file using a AVR programmer of your choice. Set the ATmega168V fuses as shown below.\\ | ||
| + | \\ | ||
| + | Fuses settings for the AVR ATmega168V in AVR-Studio:{{:wavebubble:avr_fusesettings.jpg}}\\ | ||
| + | \\ | ||
| + | To run the tests connect the Wavebubble2010 via USB and open a terminal programm. Set the terminal to 19200Baud 8N1.\\ | ||
| + | Rest should be self explaining. Type characters to run tests from the menu. | ||
/home/ladyada/public_html/wiki/data/pages/wavebubble/wave_bubble_2010.txt · Last modified: 2016/01/28 18:05 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
