products:microtouch:index.html
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
products:microtouch:index.html [2011/01/27 20:18] ladyada |
products:microtouch:index.html [2016/01/28 18:05] (current) |
||
|---|---|---|---|
| Line 88: | Line 88: | ||
| {{ :products:microtouch:microbacklight.gif |}} | {{ :products:microtouch:microbacklight.gif |}} | ||
| - | The LCD has 4 backlight white LEDs in parallel. We use a 22-68 ohm resistors (the image shows 68, the value may change depending on how bright the TFT backlight is for the current model) on each Cathode (K) and drive the cathode with a NPN connected to pin **PC6**. You can dim the backlight by software-PWMing the pin (there is no hardware PWM on that pin). For the most part either the backlight is on or off. When off, the display is not visible. | + | The LCD has 4 backlight white LEDs in parallel. We use a 22-68 ohm resistors (the image shows 68, the value may change depending on how bright the TFT backlight is for the current model) on each Cathode (K) and drive the cathode with a NPN connected to pin **PC6**. You can dim the backlight by changing the hardware PWM value of the pin. When off, the display is not visible - it is transmissive, not transflective. |
| ===== microSD/transflash card ===== | ===== microSD/transflash card ===== | ||
| {{ :products:microtouch:microsd.gif |}} | {{ :products:microtouch:microsd.gif |}} | ||
| - | + | ||
| + | Both MicroSD and MicroSD High Capacity cards are supported. | ||
| ===== 3-axis Accelerometer ===== | ===== 3-axis Accelerometer ===== | ||
| Line 110: | Line 112: | ||
| The USB port is also used to recharge the LiPo battery at about 250mA. You can also run the Microtouch direct from USB but because the lipo charger is connected directly to the regulator, it can't supply the full 100-150mA required (the voltage isnt buoyed by the battery). As a result, the core code will detect the voltage drop and dim the backlight. For that reason, you'll notice its dimmer without a battery | The USB port is also used to recharge the LiPo battery at about 250mA. You can also run the Microtouch direct from USB but because the lipo charger is connected directly to the regulator, it can't supply the full 100-150mA required (the voltage isnt buoyed by the battery). As a result, the core code will detect the voltage drop and dim the backlight. For that reason, you'll notice its dimmer without a battery | ||
| - | ===== Bootloader ===== | + | ====== Bootloader ====== |
| You don't need an AVR programmer to use this board, we put a nice bootloader on there already! The bootloader is activated by pressing the RESET/BOOT button while plugged into USB. You can tell the bootloader is active when the **green 'Boot' LED pulses/breathes** The board will then show up as a Serial or COM port, and you can use **avrdude** to program it. The 'programmer name' is **avr109** so for example, to test you should run **avrdude -p m32u4 -P COM3 -c avr109** which will initialize the bootloader. | You don't need an AVR programmer to use this board, we put a nice bootloader on there already! The bootloader is activated by pressing the RESET/BOOT button while plugged into USB. You can tell the bootloader is active when the **green 'Boot' LED pulses/breathes** The board will then show up as a Serial or COM port, and you can use **avrdude** to program it. The 'programmer name' is **avr109** so for example, to test you should run **avrdude -p m32u4 -P COM3 -c avr109** which will initialize the bootloader. | ||
| Line 122: | Line 124: | ||
| If you're using windows, you will need an **inf** driver file, you can download it below (in the **Downloads** section). Mac/Linux peeps don't as it shows up as a 'generic' serial port in /dev/ttyUSB* or /dev/cu.* (check both and/or **dmesg**) | If you're using windows, you will need an **inf** driver file, you can download it below (in the **Downloads** section). Mac/Linux peeps don't as it shows up as a 'generic' serial port in /dev/ttyUSB* or /dev/cu.* (check both and/or **dmesg**) | ||
| + | |||
| + | {{:products:microtouch:microtouchcdcboot.zip|Here is a copy of the bootloader, makefile and a bat file to show how we program microtouches}} | ||
| ====== Apps! ====== | ====== Apps! ====== | ||
| Line 141: | Line 145: | ||
| {{ :products:microtouch:imageslide_t.jpg |:products:microtouch:imageslide_t.jpg}} | {{ :products:microtouch:imageslide_t.jpg |:products:microtouch:imageslide_t.jpg}} | ||
| + | |||
| + | Troubleshooting: The files on the SD card might not show up immediately upon bootup. When using cards 2GB or larger, if the image icons do not appear, go to the HWTest app and ensure that it confirms the card is ready. After leaving the HWTest app, the icons appear. | ||
| ===== Off ===== | ===== Off ===== | ||
| Line 208: | Line 214: | ||
| * [[https://github.com/adafruit/microtouch|PCB files in EagleCAD format are available from Adafruit's github]] (CC attrib/share like) | * [[https://github.com/adafruit/microtouch|PCB files in EagleCAD format are available from Adafruit's github]] (CC attrib/share like) | ||
| * [[https://github.com/rossumur/microtouch|Firmware core including image converter is all available from Rossum's github]] (MIT license) | * [[https://github.com/rossumur/microtouch|Firmware core including image converter is all available from Rossum's github]] (MIT license) | ||
| + | * [[http://www.adafruit.com/datasheets/atmega32u4cdc.inf|Bootloader INF file for windows (mac/linux don't need a driver)]] | ||
| To develop code, you'll need an install of the AVR-gcc tool chain. | To develop code, you'll need an install of the AVR-gcc tool chain. | ||
/home/ladyada/public_html/wiki/data/attic/products/microtouch/index.html.1296159527.txt.gz · Last modified: 2016/01/28 18:05 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
