AdaWiki

Link to this comparison view

--- mdcpickandplace:diytray [2010/10/12 00:59]
ladyada
+++ mdcpickandplace:diytray [2016/01/28 18:05] (current)
@@ Line 1: / Line 1: @@
-<iframe src="http://player.vimeo.com/video/15752459" width="400" height="225" frameborder="0"></iframe><p><a href="http://vimeo.com/15752459">This old pick and place - making a tray</a> from <a href="http://vimeo.com/adafruit">adafruit industries</a> on <a href="http://vimeo.com">Vimeo</a>.</p>
+{{ vimeo>15752459 }}
 ----
@@ Line 7: / Line 6: @@
-  * [[http://www.mcmaster.com/itm/find.asp?searchstring=5537T104 | 20mm Extrusion 2 ft piece]] (McMaster #5537T104) x **2 pieces**
+  * [[http://www.mcmaster.com/#5537T104 | 20mm Extrusion 2 ft piece]] (McMaster #5537T104) x **2 pieces**
-  * [[http://www.mcmaster.com/itm/find.asp?searchstring=5537T154|20mm Extrusion T-nuts]] (McMaster #5537T154) x **4 bags of 4**
+  * [[http://www.mcmaster.com/#5537T154|20mm Extrusion T-nuts]] (McMaster #5537T154) x **4 bags of 4**
-  * [[http://www.mcmaster.com/itm/find.asp?searchstring=92137A412|Flange Button Head Cap Screw, M5 Size, 8 mm Length, 0.80 mm Pitch]] (McMaster #92137A412) x **1 bag**
+  * [[http://www.mcmaster.com/#92137A412|Flange Button Head Cap Screw, M5 Size, 8 mm Length, 0.80 mm Pitch]] (McMaster #92137A412) x **1 bag**
-  * [[http://www.mcmaster.com/itm/find.asp?searchstring=5537T181|20mm Extrusion 90 Degree Bracket, Single, 2-Hole]] (McMaster #537T181) x **4 pieces**
+  * [[http://www.mcmaster.com/#5537T181|20mm Extrusion 90 Degree Bracket, Single, 2-Hole]] (McMaster #537T181) x **4 pieces**
-  * [[http://www.mcmaster.com/itm/find.asp?searchstring=5537T14|20mm Extrusion endcap]] (Mcmaster #537T14) x **4 pieces**
+  * [[http://www.mcmaster.com/#5537T14|20mm Extrusion endcap]] (Mcmaster #537T14) x **4 pieces**
+  * [[http://www.mcmaster.com/#8560K172&sesnextrep=343409141868956|Clear Cast Acrylic Sheet, .060" Thick, 12" X 24"]] (Mcmaster #8560K172) x **1 piece**
+Total is $50
+====== Quick instructions ======
+Cut the 20mm extrusion into ~18" pieces (make them a little shorter than the pick and place drawer.
+Attach the pieces with L-brackets so that the L-brackets face each other on the inside of the holder and the outside right edge is flush with the drawer. Keep the left side loose for later adjustment
+Cut two rails from 1/16" material with 5mm drill holes so that the top edge doesnt rise above the JEDEC tray thickness
+Attach the rails with T-slot nuts.
+Place the tray on the holder, slide the left side in and tighten.

AdaWiki

User Tools

Site Tools

Page Tools